Ways to move a grand piano

Pianos routinely make movers annual list of items that are most frequently damaged. Grand pianos are especially problematic. Practicing the following procedures for dismantling, padding and loading grand pianos will prevent damage, lower claims expenditure, and enhance client satisfaction.

1) At least three individuals are required to handle a baby grand piano. If the child grand piano requires to go up or down stairs or if a full or concert grand piano requires to be transported, a minimum of four individuals are required.

2) Constantly finish a comprehensive and accurate stock. It may be essential or more suitable to use a visual stock to properly describe and reveal pre-existing damage.

3) As various parts are taken apart, please location all hardware in an appropriately identified parts bag and after that place the parts bag in a "Parts Box".

4) Get rid of the music rack (lyre) from its track by pulling it toward the keyboard. Wrap it in a clean furnishings pad.

5) Disconnect the cover by getting rid of the hinge pins. Have a single person wiggle the lid, holding it opposite the hinge, while a second individual works the pin loose. Please take care not to harm the wood with the pliers or with the pin itself. Cover the jaws of the pliers with a small fabric to assist avoid damage to the wood if necessary. Wrap the lid in a tidy furniture pad.

6) Remove the prop that holds the lid open and wrap it in a clean furnishings pad. The prop has a hinge pin and remains in 2 pieces.

7) Get rid of the pedal assembly and cover it in a tidy furnishings pad. The braces at the back of the assembly rest in slots at each end. When removing the screws, please take care not to drop the braces. In addition, please be especially careful with the push-rods so that they will not get bent. As you deal with the piano, number the push-rods from delegated right as "1", "2", and "3", by putting a piece of masking tape with the appropriate number on each rod. Note: If masking tape is unavailable, please usage properly labeled parts bags for this purpose. When reassembling at destination, please be sure to put the rods in the proper order so that the pedals will work effectively.

8) Pad the piano by placing a tidy rolled furnishings pad (stretch-wrap the pad to prevent it from unrolling) on the cover of the check over here keyboard to prevent it from flopping open while you manage the piano. Cover the top of the piano with two tidy furniture pads, nicely folded around the keyboard. Use elastic band to secure the pads. Keep in mind: Please ensure that the surface of the piano is dust-free prior to padding it. Padding a highly refined surface that is dusty might trigger fine scratches, specifically on a black lacquer finish.

9) Position a piano board and connect the straps so that it is all set to get the piano. The raised brace on the piano board must be at the keyboard end of the piano.

10) Remove the left front leg by positioning someone below the piano at the left end of the keyboard. The other 2 individuals ought to support the left front corner. The individual underneath the piano must turn the keeping block so that the long end points away from the leg. The screws, if there are any, must then be gotten rid of. The "beneath" individual should then get out from under the piano prior to actually removing the leg. Be sure to have two individuals raising the corner of the piano while the 3rd individual gets rid of the leg. Keep in mind: Please make sure to note which legs were removed from which positions because some pianos have legs that are not interchangeable.

11) Location the piano on the piano board by lowering the "leg-less" end onto the board. Please be sure to raise the whole piano slightly while completing this maneuver to avoid undue pressure on the remaining, attached legs as the piano pointers. Be great post to read sure that the piano is focused snugly against the brace at the end of the piano board.

12) Eliminate the 2 staying legs and cover them in tidy furniture pads. These legs are kept in location by a "crucial and slot" plan. To remove the leg, slide it inward toward the center of the piano until it comes out of the slot.

13) Protect the piano to the piano board by bringing completions of the straps together and attaching them. Location folded burlap pads over the furnishings pads however under the straps to supply extra defense to the edges of the piano. To prevent the strap near the narrow end of the piano from slipping off, tie the loose ends of the two straps together.

14) To move the piano over a flat, level surface area, tilt the piano and piano board and location a four-wheel dolly under the center of the piano board.

15) To move the piano up or down stairs, utilize the piano board as a skid. After adequately padding the stairs for security against residence damage, put the keyboard end of the piano toward the bottom of the stairs. Attach a bulge strap to the leading end of the Get More Information piano board to prevent the piano from slipping.

16) To load the piano, leave it on the piano board and place it in a tier as the very first base product with the keyboard dealing with the wall of the preceding tier. The finest place to load the cushioned cover is between the piano and the preceding tier or in between the wall and the piano.

Although grand pianos represent a significant obstacle, they can be moved without damage by utilizing sound judgment and practicing the treatments listed above.

Leave a Reply

Your email address will not be published. Required fields are marked *